View TA8231LQ_1057782.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TA8231LQ
TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic
TA8231LQ
42W BTL x 2CH Audio Power IC
The TA8231LQ is BTL audio power amplifier for consumer application. It is designed for high power,low distortion and low noise. It contains various kind of protectors and the function of stand-by.
Feature
* High power : POUT (1) = 42W (typ.) (VCC = 14.4V, f = 1kHz, THD = 10%, RL = 2) : POUT (2) = 37W (typ.) (VCC = 13.2V, f = 1kHz, THD = 10%, RL = 2) : POUT (3) = 22W (typ.) (VCC = 13.2V, f = 1kHz, THD = 10%, RL = 4) * Excellent output power bandwidth : POUT (4) = 17W (typ.) (VCC = 13.2V, f = 20Hz~20kHz, THD = 1%, RL = 4) * Fixed voltage gain : GV = 32dB (typ.) VCC = 13.2V, Vout = 0.775Vrms (0dBm) * * Low thermal resistance : j-c = 1.5C / W (typ.) Low distortion : THD = 0.02% (typ.) (VCC = 13.2V, f = 1kHz, Pout = 4W, RL = 4) * Built-in stand-by switch function : ISTBY = 100A (typ.) (With pin(1) set at high, power is turned on) * * Built-in various protection circuit : Thermal shut down,Over voltage,Out to GND,Out to VCC,Out to Out short Operating supply voltage : VCC (opr) = 9~18V Weight: 9.8g (typ.)
1
2004-09-28
TA8231LQ
Block Diagram
(GV = 32dB)
Caution And Application Method
(Description is made only on the single channel.) 1. Voltage gain adjustment This IC has no NF (negative feedback) terminals. Therefore, the voltage gain can't adjusted, but it makes the device a space and total costs saver. The voltage gain is decided only internal by expression below.
G V = 20log R f1 + 6 (dB) = 32 (dB) R f2
2
2004-09-28
TA8231LQ
2. Stand-by SW function By means of controlling pin(1) (stand-by terminal) to high and low,the power supply can be set to on and off. The threshold voltage of pin(1) is set at about 3V (typ.), and the power supply current is about 100A (typ.) at the stand-by state. Pin (1) control voltage: V (SB)
Stand-by On Off Power Off On V (SB) (V) 0~2 3~VCC
~Advantage of stand-by SW~ (1) Since VCC can directly be controlled to on / off by the microcomputer, the switching relay can be omitted. (2) Since the control current is microscopic, the switching relay of small current capacity is satisfactory for switching.
3. Preventive measure against oscillation For preventing the oscillation, it is advisable to use C4, the condenser of polyester film having small characteristic fluctuation of the temperature and the frequency. The resistance R to be series applied to C4 is effective for phase correction of high frequency, and improves the oscillation allowance. Since the oscillation allowance is varied according to the causes described below, perform the temperature test to check the oscillation allowance. (1) Capacity value of condenser (2) Kind of condenser (3) Layout of printed board
3
2004-09-28
TA8231LQ
Maximum Ratings (Ta = 25C)
Characteristic Peak supply voltage (0.2s) DC supply voltage Operating supply voltage Output current (peak) Power dissipation Operating temperature Storage temperature Symbol VCC (surge) VCC (DC) VCC (opr) IO (peak) PD Topr Tstg Rating 50 25 18 9 50 -30~85 -55~150 Unit V V V A W C C
Electrical Characteristics
(unless otherwise specified VCC = 13.2V, f = 1kHz, Rg = 600, Ta = 25C)
Characteristic Quiescent current Symbol Iccq Pout (1) Pout (2) Pout (3) Pout (4) Total harmonic distortion Voltage gain Voltage gain ratio THD GV GV VNO (1) VNO (2) Test Cir- cuit Vin = 0 VCC = 14.4V, THD = 10%, RL = 2 THD = 10%, RL = 2 THD = 10%, RL = 4 THD = 1%, f = 20Hz~20kHz, RL = 4 Pout = 4W Vout = 0.775Vrms (0dBm) Vout = 0.775Vrms (0dBm) Rg = 0, DIN45405 Noise Filter Rg = 0, BW = 20Hz~20kHz fripple = 100Hz, Vout = 0.775Vrms (0dBm), Rg = 600 Rg = 600, Vout = 0.775Vrms (0dBm) Vin = 0 Pin(1): GND Condition Min 28 19 30.5 -1 Typ. 150 42 37 22 17 0.02 32 0 0.07 0.06 Max 250 0.2 33.5 1 0.1 Unit mA W W W W % dB dB mVrms mVrms
Output power
Output noise voltage
Ripple rejection ratio
R.R.
40
60
dB
Cross talk Input resistance Output offset voltage Stand-by current
C.T. RIN Voffset ISTBY

-200
60 30 0 100
200 150
dB k mV A
4
2004-09-28
TA8231LQ
Test Circuit
(GV = 32dB)
5
2004-09-28
TA8231LQ
6
2004-09-28
TA8231LQ
7
2004-09-28
TA8231LQ
8
2004-09-28
TA8231LQ
Package Dimensions
Weight: 9.8g (typ.)
9
2004-09-28
TA8231LQ
About solderability, following conditions were confirmed * Solderability (1) Use of Sn-63Pb solder Bath * solder bath temperature = 230C * dipping time = 5 seconds * the number of times = once * use of R-type flux (2) Use of Sn-3.0Ag-0.5Cu solder Bath * solder bath temperature = 245C * dipping time = 5 seconds * the number of times = once * use of R-type flux
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
030619EBF
* The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. * This product generates heat during normal operation. However, substandard performance or malfunction may cause the product and its peripherals to reach abnormally high temperatures. The product is often the final stage (the external output stage) of a circuit. Substandard performance or malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the product.
10
2004-09-28

▲Up To Search▲

Price & Availability of TA8231LQ

	To Download TA8231LQ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .